Just How to Replace a Bath Tub
Just How to Replace a Bath Tub
Blog Article
We have uncovered this article involving How to Install a Bathtub below on the net and figured it made good sense to talk about it with you on this page.
Installing a tub isn't exactly brain surgery, however it does require solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a new one is additionally a moderately tough task. If the old tub is easily available, the task can move rapidly; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the task is much harder. In either instance, the job is within a house handyman's abilities, although you will certainly need an assistant to vacate the old tub and set in the brand-new one. Make certain you have actually certified yourself for the task and fit trying it. Rather than working with a specialist to take over a halfway-completed task, it is better to think about using one prior to you begin. Possibilities are you may need a professional plumber to make tube links.
This article will assist you mount a new bathtub in your washroom if you have currently gotten a brand-new bathtub and also don't require to transform the setup of your previous water pipes.
Your devices as well as material list must make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be fairly troublesome because of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to moving on to fit the new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin ensuring that the washers remain in location between the tap and the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The former type should be connected to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Using both wood boards under its feet, put the bathtub in the required placement. The wood boards are useful in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bathtub until the level checks out degree.
To set up taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water supply as well as examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Load the tub as well as additionally inspect the overflow electrical outlet as well as the regular electrical outlet for leaks.
Lastly, fix the bath paneling as described in the manufacturer's user's manual. Tiling as well as securing around the bathtub needs to wait up until the tub has been utilized at least once as this will certainly settle it right into its last placement.
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both taps making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to break a stiff seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, bring about problems with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the bath tub with water before sealing, to permit the activity experienced when the bathtub is in usage. The sealant can split relatively early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently offered on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our post on Tools You Need to Install a New Bathtub . Thank you for finding the time to read through our short article. Sharing is caring. You won't know, you could be doing someone a favor. I love reading our article about How to Install a Bathtub Yourself.
Rates Report this page